Russound CAM6.6X-S1 Instruction Manual Download Page 66

Page: 66 / 116

b. Selected: Unassigned

Selected command and subsequent commands are cleared.

(Unasg)

Procedure advances to COMMAND NUM (step 3)

c. Selected: Default

Default selects the same device type and device code previously

(Deflt)

setup in BASIC SETUP. Procedure advances to KEY FUNCTION
(step 6)

d. Selected: Macro:

i. MACRO

A macro can “call” another macro if a sequence of more than 10

(Macro)

commands is needed.

ii. MACRO ID

–

Enter the macro ID number. Menu advances to COMMAND NUM

(MacID)

(step 3)

e.Selected: Delay

Enter a 1- to 60-second delay time to postpone delivery of the

(Delay)

next command in the macro. Procedure advances to COMMAND
NUM (step 3)

f. All Other Selections:

Procedure advances to DEVICE CODE (step 5)

5. DEVICE CODE –

Source component code for IR control.

(DevCd)

6. KEY FUNCTION –

Select a function (Play, etc.).

(KeyFn)

SYSTEM INFO (SInfo)

System Info allows the installer to view the controller’s manufacturing build properties.

See System Info - Flow Chart page 79

#CONTROLLERS (#Ctls)

BUILD TIME (BTime)

BUILD DATE (BDate)

VERSION (Ver)

1. #CONTROLLERS

Displays the number of CAM6.6 controllers in the system.

(#Ctls)

2. BUILD TIME

Displays the Software Build Time of the controller.

(BTime)

3. BUILD DATE

Displays the Software Build Date of the controller.

(BDate)

4. VERSION

Displays the software version of the CAM6.6.

(Ver)

INSTALLER

INSTALLATION MENU

Summary of Contents for CAM6.6X-S1




















































































































Search results

Summary of Contents for CAM6.6X-S1

Reviews:

Related manuals for CAM6.6X-S1

Brands by name

Popular brands

Russound CAM6.6X-S1, Instruction Manual

Search results

Summary of Contents for CAM6.6X-S1

Reviews:

Related manuals for CAM6.6X-S1

Brands by name

Popular brands