Russound CAM6.6X-S1 Instruction Manual Download Page 52 | Manualshive

Page: 52 / 116

background image

52

INSTALLER

INSTALLATION MENU OVERVIEW

There are three item types in the installation menu:

Menu Item (m) –

Acts as a folder that holds procedures and/or feature parameters.

Procedure (p) –

A sequence of feature parameters to perform a guided operation, such as
configuring an UNO key. Once you begin a procedure, the system will prompt for
the needed information to complete the task.

Feature (f) –

The actual parameters (settings) that will change the system configuration.

The following keys on the

UNO-S2

keypad are used to navigate and make changes while using the

installation menus:

To enter the Installation Menu, press and release the Setup Button (located on the keypad’s right

side) while in normal operating mode. The Setup Button is used to “back out” of the Installation Menu
one level at a time. If you are performing a procedure, the Setup Button brings you back to the
beginning of the procedure. Once you have reached the top level of the Installation Menu, pressing
the Setup Button brings you back to normal operating mode.

Adjust feature setting (increment).

Adjust feature setting (decrement).

Go to next menu / procedure / feature. Not available while performing a procedure.

Go to previous menu / procedure / feature. Not available while performing a procedure.

Enter menu / begin procedure / show current feature setting. While performing a procedure, it is

also used to advance to the next sequential feature setting once the current feature has been viewed
or adjusted.

UNO-S1 Keypad Five-Character Display

The UNO-S1 keypad abbreviates information as necessary to appear in its five-character display. In
the following menu procedures, the UNO-S1 five-character abbreviation is shown in parentheses
underneath the 12-character version.

«
...
50
51
52
53
54
...
»

Summary of Contents for CAM6.6X-S1





















































































































Reviews:

No comments

Related manuals for CAM6.6X-S1

Brand: Caliber Pages: 23

Brand: Yamaha Pages: 137

Brand: Yamaha Pages: 94

Brand: Chiayo Pages: 8

Brand: FTE Pages: 24

Brand: Icom Pages: 47

Brand: Axxera Pages: 32

Brand: Aiwa Pages: 5

Brand: Vauxhall Pages: 137

Brand: DAAB Pages: 8

Brand: EZCast Pro Pages: 33

Brand: ST Group Pages: 61

Brand: Harman Kardon Pages: 176

Brand: Vertex Pages: 32

SEL2641 R433-Z2

Brand: Erone Pages: 2

EDACS 19D902120G1

Brand: Ericsson Pages: 14

Brand: Icom Pages: 36

Brand: Harris Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands