Russound CAM6.6X-S1 Instruction Manual Download Page 62 | Manualshive

Page: 62 / 116

background image

62

INSTALLER

INSTALLATION MENU

disabled zone. If enabled, an All On command activated from
another zone will turn on the enabled zone.

3. PARTY ENABLE -

This feature is either disabled or enabled. If disabled, Party Mode

(PtyEn)

activation from another zone will not affect the disabled zone. If
enabled (default), the zone will participate with Party Mode.

4. MASTER ENABLE -

This feature is either disabled or enabled. If disabled, the zone

(MstEn)

cannot host a master keypad during Party Mode. If enabled
(default), the zone has the option of hosting the Master keypad.

5. MUTE ENABLE -

This feature is either disabled or enabled. It allows the option of

(MutEn)

enabling or disabling muting in a zone. If disabled, the zone will
not mute. If enabled (default), the zone will be muted when a
mute signal is received.

CTRLR SETUP (CtlId)

Controller Setup is the basic configuration of the controller. This setup menu selects the options for
Controller ID and Factory Initialization.

See Controller Setup - Flow Chart page 75

1. CONTROLLER ID -

This defines the Controller ID for this system. The default is 1 but

(CtlId)

when multiple controllers are used, each additional controller ID
must be sequential and unique and be set before being connect-
ed to the system. Note that the system must be restarted before
the controller will assume the new ID.

2. FACTORY INIT -

WARNING: This procedure returns the controller to its

(FInit)

original settings - use with discretion.

Factory Initialization allows the installer to erase all programmed
settings and returns the settings to the factory default settings.
All settings including source equipment IR commands will need to
be reentered. An “Are you sure?” prompt and a “no” response
allows the installer to cancel the reset; a “yes” at the prompt will
load factory/default settings.

POWER MANAGEMENT (PwMgt)

The CAM6.6 is capable of managing the power state of the connected source equipment. The power
management is configured on a source-by-source basis.

«
...
60
61
62
63
64
...
»

Summary of Contents for CAM6.6X-S1





















































































































Reviews:

No comments

Related manuals for CAM6.6X-S1

MS4200RS - Navigation System With CD Player

Brand: Jensen Pages: 65

Brand: Sangean Pages: 1

Brand: Alinko Pages: 48

Brand: JDM Pages: 8

Brand: CEBEK Pages: 2

Brand: Ocean Signal Pages: 28

Brand: Onkyo Pages: 111

Brand: B&K Pages: 12

Brand: Beltek Pages: 16

Brand: uAvionix Pages: 31

Brand: SecurityMan Pages: 17

Brand: PowerBass Pages: 12

Brand: F.u.n.k.e. Pages: 81

Brand: Sangean Pages: 1

Brand: Hallicrafters Pages: 13

Brand: Zodiac Pages: 50

Brand: Kenwood Pages: 47

Brand: Kenwood Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands