Royal Alpha 710ML User Manual Download | Manualshive

Page: 126 / 134

background image

Appendix A

119

Alpha 710ML User’s Guide

Safety and Legal Notices

• The power outlet for this cash register must be located near the unit and

be easily accessible.

• Do not use this cash register outdoors in the rain or near any source of

liquid, such as a pool.

• The back-up power system: When you are not using your cash register,

keep it plugged in with the cash register turned OFF from the main
menu. If the unit is unplugged, back-up power for the memory is
provided through the batteries, but this should not be used for long
periods of time.

FEDERAL COMMUNICATIONS COMMISSION (FCC) RADIO FREQUENCY
INTERFERENCE STATEMENT INFORMATION TO THE USER

CAUTION: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a
ClassB digital device, pursuant to Part15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. If applicable, connect the equipment into an outlet on a circuit different from that to
4. which the receiver is connected.

Consult the dealer or an experienced radio / TV technician for assistance.

Connection of peripherals to this unit requires the use of grounded, shielded cables to
ensure compliance with the ClassB FCC limits.

IN CANADA:

This digital apparatus does not exceed the Class limits for radio noise emissions from
digital apparatuses set forth in the Radio Interference Regulations of the Canadian
Department of Communications.

Proposition 65 Notice

The following is given in accordance with California Proposition 65.

WARNING

: This product contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

Wash hands after handling

.

«
...
124
125
126
127
128
...
»

Summary of Contents for Alpha 710ML







































































































































Reviews:

No comments

Related manuals for Alpha 710ML

Brand: Samsung Pages: 43

Brand: Sharp Pages: 10

Brand: Sharp Pages: 2

Brand: Sharp Pages: 2

Brand: Sharp Pages: 8

Brand: Sharp Pages: 22

Brand: Sharp Pages: 30

Brand: Sharp Pages: 37

Brand: Sharp Pages: 76

Brand: Sharp Pages: 63

Brand: Sharp Pages: 64

Brand: Sharp Pages: 64

Brand: Sharp Pages: 64

Brand: Sharp Pages: 59

Brand: Sharp Pages: 82

Brand: Sharp Pages: 79

Brand: Sharp Pages: 82

Brand: Sharp Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands