manualshive.com logo in svg

Ross LDP-8242, User Manual, Page: 9 / 100

Share
Download
Ross LDP-8242 User Manual Download Page 9

LDP-8242 User Manual (Iss. 03)

Introduction • 1–1

Introduction

In This Chapter

This chapter contains the following sections:

• Overview
• Manual Overview
• Functional Block Diagram
• Video Subsystem Overview
• Audio Subsection Overview
• Control and Data Input/Output Interfaces
• User Control Interface
• Documentation Terms and Conventions

A Word of Thanks

Congratulations on choosing an openGear LDP-8242 Multi-Definition Loudness Processor. Your 
LDP-8242 is part of a full line of Digital Products within the openGear Terminal Equipment 
family of products, backed by Ross Video’s experience in engineering and design expertise since 
1974.

You will be pleased at how easily your new LDP-8242 fits into your overall working 
environment. Equally pleasing is the product quality, reliability and functionality. Thank you for 
joining the group of worldwide satisfied Ross Video customers!

Should you have a question pertaining to the installation or operation of your LDP-8242, please 
contact us at the numbers listed on the back cover of this manual. Our technical support staff is 
always available for consultation, training, or service.

Summary of Contents for LDP-8242





































































































Reviews:

No comments