manualshive.com logo in svg

Ross LDP-8242, User Manual, Page: 40 / 100

Share
Download
Ross LDP-8242 User Manual Download Page 40

3–6 • Operating Instructions

LDP-8242 User Manual (Iss. 03)

Accessing the Card via DashBoard™

Access the LDP-8242 card using DashBoard™ as described below. 

Accessing the Card via DashBoard

1.

On the computer connected to the frame LAN, open DashBoard™.

2.

As shown below, in the left side Basic View Tree, locate the frame containing the 
LDP-8242 card to be accessed (in this example, Frame 1A).

Basic Tree View — Selecting the Frame

3.

As shown below, expand the tree to access the cards within the frame. Select the card to 
be accessed (in this example, Slot 7: LDP-8242).

.

Basic Tree View — Selecting the LDP-8242

As shown on 

Figure 3.4

, when the card is accessed in DashBoard™ its function 

submenu screen showing tabs for each function is displayed. (The particular submenu 
screen displayed is the previously displayed screen from the last time the card was 
accessed by DashBoard™).

Summary of Contents for LDP-8242





































































































Reviews:

No comments