manualshive.com logo in svg

Ross LDP-8242, User Manual, Page: 61 / 100

Share
Download
Ross LDP-8242 User Manual Download Page 61

LDP-8242 User Manual (Iss. 03)

Operating Instructions • 3–27

Input Audio Status

Displays signal status for embedded and discrete audio received by the 

card.

Individual signal status and peak level displays for embedded audio channel pairs 1-2 thru 15-16 and AES pairs 1 thru 8, and 

analog audio input pairs 1-2 thru 7-8 as follows:

•

Unlocked

: Indicates AES pair or embedded channel does not contain recognized audio PCM data.

•

PCM

: Indicates AES pair or embedded channel contains recognized AES audio PCM data.

•

Dolby E

: Indicates AES pair or embedded channel contains Dolby® E encoded data.

•

Dolby Digital

: Indicates AES pair or embedded channel contains Dolby® Digital encoded data.

Note

: Dolby status displays shown to the left only occur for valid Dolby® signals meeting SMPTE 337M standard.

If a Dolby pair is passed through the card without decoding, the signal is passed with all related gain controls set to unity.

Note

: After familiarizing yourself with the controls described in the audio routing/control sections that follow, refer to the section 

“

Troubleshooting

” on page 3-51 for a comprehensive example using these controls for multi-source audio routing.

Summary of Contents for LDP-8242





































































































Reviews:

No comments