Ross LDP-8242 User Manual Download Page 49

Page: 49 / 100

LDP-8242 User Manual (Iss. 03)

Operating Instructions • 3–15

(continued)

ATC_VITC Legacy Support Control

When enabled, accommodates equipment requiring ATC_VITC packet in

both fields as a “field 1” packet (non-toggling).

Note

: Non-toggling VITC1 and VITC2 packets do not conform to

SMPTE 12M-2-2008 preferences. As such, ATC_VITC Legacy

Support should be enabled only if required by downstream

equipment.

Free Run Timecode Controls

Allows an initial (starting) count to be applied to output video timecode

when Free Run insertion is enabled.

Note

: Initialization can only be applied when card is outputting Free

Run timecode (as shown by Output Status displaying “Free Run”).
If failover to Free Run occurs due to loss of external timecode(s),

the Free Run count assumes its initial count from the last valid

externally supplied count.

Summary of Contents for LDP-8242





































































































Search results

Summary of Contents for LDP-8242

Reviews:

Ross LDP-8242, User Manual, Page: 49 / 100

Search results

Summary of Contents for LDP-8242

Reviews: