manualshive.com logo in svg

Ross LDP-8242, User Manual, Page: 28 / 100

Share
Download
Ross LDP-8242 User Manual Download Page 28

2–2 • Installation

LDP-8242 User Manual (Iss. 03)

Before You Begin

Before proceeding with the instructions in this chapter, ensure that your DFR-8321 series frame is 
properly installed according to the instructions in the 

DFR-8300 Series User Manual

.

Static Discharge

Throughout this chapter, please heed the following cautionary note: 

   

Unpacking

Unpack each card you received from the shipping container and ensure that all items are included. 
If any items are missing or damaged, contact your sales representative or Ross Video directly.

ESD Susceptibility

 — Static discharge can cause serious damage to sensitive 

semiconductor devices. Avoid handling circuit boards in high static environments such as 
carpeted areas and when synthetic fiber clothing is worn. Always exercise proper grounding 
precautions when working on circuit boards and related equipment.

This card contains semiconductor devices which are susceptible to serious damage from 
Electrostatic Discharge (ESD). ESD damage may not be immediately apparent and can affect 
the long-term reliability of the device.

Summary of Contents for LDP-8242





































































































Reviews:

No comments