manualshive.com logo in svg

Ross LDP-8242, User Manual, Page: 8 / 100

Share
Download
Ross LDP-8242 User Manual Download Page 8

ii • Contents

LDP-8242 User Manual (Iss. 03)

Function Submenu/Parameter Submenu Overview............................................... 3-2

Card-edge Controls, Indicators, and Display ....................................................................... 3-3

Card-edge Controls ................................................................................................ 3-3

DashBoard™ User Interface ................................................................................................ 3-5
Accessing the Card via DashBoard™.................................................................................. 3-6

Accessing the Card via DashBoard ....................................................................... 3-6

Checking Card Information.................................................................................................. 3-8
Ancillary Data Line Number Locations and Ranges ........................................................... 3-9
Function Submenu List and Descriptions .......................................................................... 3-10
Troubleshooting ................................................................................................................. 3-51

Error and Failure Indicator Overview.................................................................. 3-51
Basic Troubleshooting Checks ............................................................................ 3-55
Processing Error Troubleshooting ....................................................................... 3-55
In Case of Problems............................................................................................. 3-56

Specifications

4

Technical Specifications ...................................................................................................... 4-2

Service Information

5

Troubleshooting Checklist ................................................................................................... 5-2
Warranty and Repair Policy ................................................................................................. 5-3

Summary of Contents for LDP-8242





































































































Reviews:

No comments