manualshive.com logo in svg

Ross LDP-8242, User Manual, Page: 46 / 100

Share
Download
Ross LDP-8242 User Manual Download Page 46

3–12 • Operating Instructions

LDP-8242 User Manual (Iss. 03)

Timecode

Provides timecode data extraction from various sources, and provides 

formatting and re-insertion controls for inserting the timecode into the 

output video.

Noting that the incoming video contains VITC 
waveform timecode data (as shown in the status 

display), set the Source Priority drop-down lists to 
include VITC Waveform timecode data (

SDI VITC

) as 

a choice. This extracts VITC Waveform timecode 
data from the incoming video.

In this example, it is desired to provide SD ATC_VITC 
timecode data in the output video. As such, set 

SD ATC VITC Insertion 

to 

Enabled

.

In the example here, the line numbers are set to the 
default SMPTE 12M-2-2008 recommended value.

Shown below is an example in which received SDI video with SDI VITC waveform timecode is to be converted to SDI 
ATC_VITC timecode data. Each Timecode control is fully described on the pages that follow.

Summary of Contents for LDP-8242





































































































Reviews:

No comments