94
Using Insertion Effects
Amp Sw (Amp Switch)
Off/On [3 (40 03 05)]
Turns the Amp Type on/off.
Low Gain
-12–+12 [17 (40 03 13)]
Adjusts the gain of the low frequency range.
Hi Gain (High Gain)
-12–+12 [18 (40 03 14)]
Adjusts the gain of the high frequency range.
#Pan (Output Pan)
L63–0–R63 [19 (40 03 15)]
Adjusts the stereo location of the output sound. L63 is far
left, 0 is center, and R63 is far right.
Level (Output Level)
0–127 [20 (40 03 16)]
Adjusts the output level.
Effects that modulate the sound (modulation type)
07: Phaser
[01H, 20H]
A phaser adds a phase-shifted sound to the original sound,
producing a twisting modulation that creates spaciousness
and depth.
fig.9-7
+Manual
100–8.0k [1 (40 03 03)]
Adjusts the basic frequency from which the sound will be
modulated.
#Rate
0.05–10.0 [2 (40 03 04)]
Adjusts the frequency (period) of modulation.
Depth
0–127 [3 (40 03 05)]
Adjusts the depth of modulation.
Reso (Resonance)
0–127 [4 (40 03 06)]
Adjusts the amount of emphasis added to the frequency
range surrounding the basic frequency determined by the
Manual parameter setting.
Mix (Mix Level)
0–127 [5 (40 03 07)]
Adjusts the proportion by which the phase-shifted sound is
combined with the direct sound.
Low Gain
-12–+12 [17 (40 03 13)]
Adjusts the gain of the low frequency range.
Hi Gain (High Gain)
-12–+12 [18 (40 03 14)]
Adjusts the gain of the high frequency range.
Level (Output Level)
0–127 [20 (40 03 16)]
Adjusts the output level.
08: Auto Wah
[01H, 21H]
The Auto Wah cyclically controls a filter to create cyclic
change in timbre.
fig.9-8
Fil Type (Filter Type)
LPF/BPF [1 (40 03 03)]
Selects the type of filter.
LPF:
The wah effect will be applied over a wide
frequency range.
BPF:
The wah effect will be applied over a narrow
frequency range.
Sens (Sensitivity)
0–127 [2 (40 03 04)]
Adjusts the sensitivity with which the filter is controlled. If
this value is increased, the filter frequency will change more
readily in response to the input level.
+Manual 0–127 [3 (40 03 05)]
Adjusts the center frequency from which the effect is
applied.
Peak 0–127 [4 (40 03 06)]
Adjusts the amount of the wah effect that will occur in the
area of the center frequency. Lower settings will cause the
effect to be applied in a broad area around the center
frequency. Higher settings will cause the effect to be
applied in a more narrow range. In the case of LPF,
decreasing the value will cause the wah effect to change
less.
#Rate 0.05–10.0 [5 (40 03 07)]
Adjusts the speed of the modulation.
Depth 0–127 [6 (40 03 08)]
Adjusts the depth of the modulation.
Polarity
Down/Up [7 (40 03 09)]
Sets the direction in which the frequency will change when
the filter is modulated. With a setting of Up, the filter will
change toward a higher frequency. With a setting of Down
it will change toward a lower frequency.
Low Gain
-12–+12 [17 (40 03 13)]
Adjusts the gain of the low frequency range for EQ.
Hi Gain (High Gain)
-12–+12 [18 (40 03 14)]
Adjusts the gain of the high frequency range for EQ.
Pan (Output Pan)
L63–0–R63 [19 (40 03 15)]
Adjusts the stereo location of the output sound. L63 is far
left, 0 is center, and R63 is far right.
Level (Output Level)
0–127 [20 (40 03 16)]
Adjusts the output level.
L
R
EQ
Phaser
Phaser
EQ
L
R
Wah
EQ
Pan
