manualshive.com logo in svg

Rointe Dalis 200DHW4, Instruction Manual

Share
Download
Rointe Dalis 200DHW4 Instruction Manual Download Page 8

8

7. Before installation

IMPORTANT
Failure to observe these instructions will invalidate the guarantee. Handling /  instal-
lation of this product is subject to the Health & Safety At Work act. This product must 
be installed by a qualified professional that is certified for Unvented Water Heater 
installation. Do not attempt to install this product yourself if you are not qualified.

7.1. Handling and transport

• 

You must not put any type of pressure on the upper part of the device, as it is not structural in 
nature. The product must be transported and handled in the upright position only. The screen 
should be facing the upper side. If tipped, the centre of gravity will shift. Please handle with care.

• 

The equipment can only be transported horizontally during the last kilometre, taking care to 
place some supports on the underside of the product in order not to lean against upper parts.

Positions allowed for transport/handling:

Positions NOT allowed for transport / handling:

Summary of Contents for Dalis 200DHW4

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands