manualshive.com logo in svg

Rointe Dalis 200DHW4, Instruction Manual

Share
Download
Rointe Dalis 200DHW4 Instruction Manual Download Page 33

33

DALIS

Digital electric unvented heat pump

If P4 = 1, d2 represents the temperature of the evaporator above which the defrosting procedure is 
completed. Vice versa, if P4 = 0 or P4 = 2, the parameter d2 is not taken into consideration.

If during the defrosting procedure the evaporator or the probe is higher than the set threshold by 
means of parameters d2 and P4 = 1, the request to activate the defrosting procedure will not be 
accepted.

The thawing procedure consists of three stages:

• 

Defrosting stage: the d3 parameter establishes the maximum length of the stage. Output status:

-  The compressor is active if d1 = 1, otherwise it is switched off.

-  The defrosting relay is active if d1 = 0 or d1 = 1, otherwise it is switched off.

-  The fans are switched on if d1 = 2, otherwise they are switched off.

• 

Dripping stage: the d7 parameter establishes the length of the stage. Output status:

-  The compressor is switched off.

-  The defrosting relay is active if d1 = 0 or d1 = 1, otherwise it is switched off.

-  The fans are switched off.

• 

Drying stage: the d16 parameter establishes the length of the stage. Output status:

-  The compressor acts according to parameter d8.

-  The defrosting relay is active if d1 = 0 or d1 = 1, otherwise it is switched off.

-  The fans are switched off.

If the “anti-legionella” or “overboost” functions are in progress, the defrosting procedure will not be 
activated.

10.5.5. Configuration parameter settings

To carry out the procedure:

• 

Make sure that the keypad is not locked and that no other advanced procedure is in progress.

• 

Press and hold the 

 buttons for 4 seconds. The screen will show “PA” (password).

• 

Press and release the 

 button.

• 

Press either the 

 

or

 

 button within 15 seconds to set “-19” on the display screen.

• 

Press and release the 

  button, or do not carry out any operation for 15 seconds.

• 

Press and hold the 

 buttons for 4 seconds. The screen will show the “SP1” parameter.

To select a parameter:

• 

Press either the 

 

or

 

 button.

To change a parameter:

• 

Press and release the 

 button.

• 

Press either the 

 

or

 

 button to increase or decrease the value of the parameter (within 

15 seconds).

Summary of Contents for Dalis 200DHW4

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands