manualshive.com logo in svg

Rointe Dalis 200DHW4, Instruction Manual

Share
Download
Rointe Dalis 200DHW4 Instruction Manual Download Page 21

21

DALIS

Digital electric unvented heat pump

8.12. Drain valve

We recommend a drain valve is installed (not supplied) in the lowest point of the cold water feed to 
the product. This allows the product to be drained in a controlled manner if necessary (see figure 5).

8.13. Condensation drain connections

Condensation formed during operation of the heat pump should flow through a purpose-built outlet 
pipe (G 1/2”) that passes inside the insulating casing and emerges on the side of the appliance. 
Connect it to a duct via a siphon so that the condensation should flow as it should.

Figure 13a - example of condensation discharge                   Figure 13b - example of condensation
pipe  connection  via  a  siphon   

 

 

  discharge  pipe  connection  via  siphon                         

       

with 

a 

water 

shut-off 

valve

      

8.14. Electrical fittings

The product is supplied already wired for the mains power supply. It is powered through a flexible 
cable and a socket/plug combination (figure 14). An earthed Type G socket (UK) with separate pro-
tection is needed for the connection to the mains power supply.

Figure 14 - type G socket and plug

 

Summary of Contents for Dalis 200DHW4

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands