manualshive.com logo in svg

Rohde & Schwarz 3560.6550.06, Operating Manual

Share
Download
Rohde & Schwarz 3560.6550.06 Operating Manual Download Page 25

ENV216

Operating Manual

3560.6550.12  -01-

3.5

E-1

Reference ground

The  network  is  connected  to  the  PE  grounding  connection  for  the  mains  power  supply  through  the

mains cable, but this is not adequate for use as a reference ground in HF noise voltage measurement.

The reference ground used can be attached flat to the grounding rail (2) on the side of the device by a

broad sheet metal  with three metric M4 screws (1).

Grounding rail on the side of housing

In order to prevent RF interference emitted by the mains grounding conductor from reaching the refer-

ence mass, the grounding conductor and the reference mass are decoupled by a PE-choke. This choke

should not be bridged by the EMI test receiver, which is also connected to the measurement reference

ground. Therefore, either an isolated or a battery-powered receiver must be used, or a PE choke must

also be placed on the PE connection of the receiver.

1

2

2

Summary of Contents for 3560.6550.06










































Reviews:

No comments

Brands by name

Popular brands

Load more brands