manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 4, User Manual

Share
Download
Rockwell Automation Allen-Bradley PowerFlex 4 User Manual Download Page 68

4-6

Troubleshooting

Drive does not Start from Integral Keypad.

Drive does not respond to changes in speed command.

Motor and/or drive will not accelerate to commanded speed.

Cause(s)

Indication

Corrective Action

Integral keypad is not enabled. Green LED above Start key is 

not illuminated.

•

Set parameter P036 

[Start 

Source]

 to option 0 “Keypad”.

•

Set parameter A051 - A052 

[Digital Inx Sel]

 to option 5 

“Local” and activate the input.

I/O Terminal 01 “Stop” input is 
not present.

None

Wire inputs correctly and/or install 
jumper.

Cause(s)

Indication

Corrective Action

No value is coming from the 
source of the command.

The drive “Run” indicator is lit 
and output is 0 Hz.

•

Check d012 

[Control Source]

 for 

correct source.

•

If the source is an analog input, 
check wiring and use a meter to 
check for presence of signal.

•

Check d002 

[Commanded Freq]

 

to verify correct command.

Incorrect reference source is 
being selected via remote 
device or digital inputs.

None

•

Check d012 

[Control Source]

 for 

correct source.

•

Check d014 

[Dig In Status]

 to 

see if inputs are selecting an 
alternate source. Verify settings 
for A051 - A052 

[Digital Inx Sel]

.

•

Check P038 

[Speed Reference]

 

for the source of the speed 
reference. Reprogram as 
necessary.

•

Review the Speed Reference 
Control chart on 

page 1-17

.

Cause(s)

Indication

Corrective Action

Acceleration time is excessive. None

Reprogram P039 

[Accel Time 1]

 or 

A067 

[Accel Time 2]

.

Excess load or short 
acceleration times force the 
drive into current limit, slowing 
or stopping acceleration.

None

Compare d003 

[Output Current]

 with 

A089 

[Current Limit]

.

Remove excess load or reprogram 
P039 

[Accel Time 1]

 or A067 

[Accel 

Time 2]

.

Check for improper A084 

[Start 

Boost]

 setting.

Speed command source or 
value is not as expected.

None

Verify d002 

[Commanded Freq]

.

Check d012 

[Control Source]

 for the 

proper Speed Command.

Programming is preventing the 
drive output from exceeding 
limiting values.

None

Check P035 

[Maximum Freq]

 to 

insure that speed is not limited by 
programming.

userman.book  Page 6  Friday, June 21, 2002  2:48 PM

Summary of Contents for Allen-Bradley PowerFlex 4































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands