manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 4, User Manual

Share
Download
Rockwell Automation Allen-Bradley PowerFlex 4 User Manual Download Page 83

Appendix

 C

RS485 (DSI) Protocol

PowerFlex 4 drives support the RS485 (DSI) protocol to allow efficient 
operation with Rockwell Automation peripherals. In addition, some 
Modbus functions are supported to allow simple networking. PowerFlex 
4 drives can be multi-dropped on an RS485 network using Modbus 
protocol in RTU mode. 

Network Wiring

Network wiring consists of a shielded 2-conductor cable that is 
daisy-chained from node to node.

Figure C.1  Network Wiring Diagram

Only pins 4 and 5 on the RJ45 plug should be wired. The other pins on 
the PowerFlex 4 RJ45 socket contain power, etc. for other Rockwell 
Automation peripheral devices and must not be connected.

Wiring terminations on the master controller will vary depending on the 
master controller used and “TxRxD+” and “TxRxD-” are shown for 
illustration purposes only. Refer to the master controller’s user manual 
for network terminations. Note that there is no standard for the “+” and 
“-” wires, and consequently Modbus device manufacturers interpret 
them differently. If you have problems with initially establishing 
communications, try swapping the two network wires at the master 
controller.

Standard RS485 wiring practices apply. Termination resistors need to be 
applied at each end of the network cable. RS485 repeaters may need to 
be used for long cable runs, or if greater than 32 nodes are needed on the 
network.

Controller

Master

PowerFlex 4

Node 1

4

5

PowerFlex 4

Node 2

4

5

PowerFlex 4

Node "n"

4

5

TxRxD+

TxRxD-

TxRxD+

TxRxD-

TxRxD+

TxRxD-

NOTE: The shield is connected at ONLY ONE end of each cable segment.

Shield

Shield

Shield

120 ohm resistor

120 ohm resistor

X

X

X

1

FRONT

userman.book  Page 1  Friday, June 21, 2002  2:48 PM

Summary of Contents for Allen-Bradley PowerFlex 4































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands