manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 4, User Manual

Share
Download
Rockwell Automation Allen-Bradley PowerFlex 4 User Manual Download Page 9

 

Overview

 

P-3

 

General Precautions

!

 

ATTENTION:  

 

The drive contains high voltage capacitors which take 

time to discharge after removal of mains supply. Before working on 
drive, ensure isolation of mains supply from line inputs [R, S, T (L1, 
L2, L3)]. Wait three minutes for capacitors to discharge to safe voltage 
levels. Failure to do so may result in personal injury or death.

Darkened display LEDs is not an indication that capacitors have 
discharged to safe voltage levels.

!

 

ATTENTION:  

 

Only qualified personnel familiar with adjustable 

frequency AC drives and associated machinery should plan or 
implement the installation, start-up and subsequent maintenance of the 
system. Failure to comply may result in personal injury and/or 
equipment damage.

!

 

ATTENTION:  

 

This drive contains ESD (Electrostatic Discharge) 

sensitive parts and assemblies. Static control precautions are required 
when installing, testing, servicing or repairing this assembly. 
Component damage may result if ESD control procedures are not 
followed. If you are not familiar with static control procedures, 
reference A-B publication 8000-4.5.2, “Guarding Against Electrostatic 
Damage” or any other applicable ESD protection handbook.

!

 

ATTENTION:  

 

An incorrectly applied or installed drive can result in 

component damage or a reduction in product life. Wiring or application 
errors, such as, undersizing the motor, incorrect or inadequate AC 
supply, or excessive ambient temperatures may result in malfunction of 
the system.

 

userman.book  Page 3  Friday, June 21, 2002  2:48 PM

Summary of Contents for Allen-Bradley PowerFlex 4































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands