Rockwell Automation Allen-Bradley PowerFlex 4 User Manual Download Page 27

Page: 27 / 94

Installation/Wiring

1-17

The drive speed command can be obtained from a number of different
sources. The source is normally determined by P038

[Speed Reference]

However, when A051 or A052

[Digital Inx Sel]

is set to option 2, 4, 5 or

6, and the digital input is active, A051 or A052 will override the speed
reference commanded by P038

[Speed Reference]

. See the chart below

for the override priority.

Start and Speed Reference Control

Jog Input

Enabled and Active:

A051 or A052 = 2

Yes

Drive will Start and Run at Jog Speed.

Direction comes from

Terminal 03 Dir/Run REV

Local/Remote Input
Enabled and Active:

A051 or A052 = 5

Yes

Start, Speed and Direction commands

come from Integral Keypad.

Comm Select Input
Enabled and Active:

A051 or A052 = 6

Yes

Start, Speed and Direction commands

come from RS485 (DSI) port.

P038 [Speed Reference]

= 4 or 5

Yes

Run as specified by

P038 [Speed Reference].

Start and Direction commands come

from P036 [Start Source].

A051 / A052

Preset Inputs Active

Yes

Run as specified by

A071-A073 [Preset Freq 1-3].

Start and Direction commands come

from P036 [Start Source].

Run as specified by

P038 [Speed Reference].

Start and Direction commands come

from P036 [Start Source].

userman.book Page 17 Friday, June 21, 2002 2:48 PM

Summary of Contents for Allen-Bradley PowerFlex 4































































































Search results

Summary of Contents for Allen-Bradley PowerFlex 4

Reviews:

Related manuals for Allen-Bradley PowerFlex 4

Brands by name

Popular brands

Rockwell Automation Allen-Bradley PowerFlex 4, User Manual

Search results

Summary of Contents for Allen-Bradley PowerFlex 4

Reviews:

Related manuals for Allen-Bradley PowerFlex 4

Brands by name

Popular brands