manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 4, User Manual

Share
Download
Rockwell Automation Allen-Bradley PowerFlex 4 User Manual Download Page 55

Programming and Parameters

3-19

Advanced Program Group 

(continued) 

A084 [Start Boost]

Related Parameter(s): 

P031

Sets the boost voltage (% of P031 

[Motor NP Volts]

) and redefines the Volts per Hz curve.

(1)

(1)

Drive may add additional voltage unless Option 5 is selected.

Options

1

“30.0”

Variable Torque

2

“35.0”

3

“40.0”

4

“45.0”

5

“0.0 no IR Comp”

Constant Torque

6

“0.0”

7

“2.5”
[Default for 3.7kW 
(5HP) Drives]

8

“5.0” (Default)

9

“7.5”

10

“10.0”

11

“12.5”

12

“15.0”

13

“17.5”

14

“20.0”

% [Motor NP Hertz]

% [Motor NP Volts]

100

50

1/2 [Motor NP Volts]

1/2

[Motor NP Hertz]

4
3
2
1

0

50

100

Settings

5-14

A088 [Maximum Voltage]

Sets the highest voltage the drive will output.

Values

Default

Drive Rated Volts

Min/Max:

20/Drive Rated Volts

Display:

1 VAC

userman.book  Page 19  Friday, June 21, 2002  2:48 PM

Summary of Contents for Allen-Bradley PowerFlex 4































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands