manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 4, User Manual

Share
Download
Rockwell Automation Allen-Bradley PowerFlex 4 User Manual Download Page 44

3-8

Programming and Parameters

Basic Program Group

 Stop drive before changing this parameter.

P031 [Motor NP Volts]

Related Parameter(s): 

A084

Set to the motor nameplate rated volts.

Values

Default

Based on Drive Rating

Min/Max:

20/Drive Rated Volts

Display:

1 VAC

 Stop drive before changing this parameter.

P032 [Motor NP Hertz]

Related Parameter(s):

A084

Set to the motor nameplate rated frequency.

Values

Default

60 Hz

Min/Max:

10/240 Hz

Display:

1 Hz

P033 [Motor OL Current]

Related Parameter(s): 

A089

, 

A090

, 

A098

Set to the maximum allowable motor current.

The drive will fault on an F7 Motor Overload if the value of this parameter is exceeded by 150% for 60 
seconds or 200% for 3 seconds.

Values

Default

Based on Drive Rating

Min/Max:

0.0/(Drive Rated Amps 

×

 2)

Display:

0.1 Amps

P034 [Minimum Freq]

Related Parameter(s): 

P035

Sets the lowest frequency the drive will output continuously.

Values

Default

0.0 Hz

Min/Max:

0.0/240.0 Hz

Display:

0.1 Hz

 Stop drive before changing this parameter.

P035 [Maximum Freq]

Related Parameter(s): 

P034

Sets the highest frequency the drive will output.

Values

Default

60 Hz

Min/Max:

0/240 Hz

Display:

1 Hz

userman.book  Page 8  Friday, June 21, 2002  2:48 PM

Summary of Contents for Allen-Bradley PowerFlex 4































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands