Rioned CityJet User Manual Download Page 85

Page: 85 / 98

MALFUNCTIONS

LED next to START button at
bottom right of the Riomote
control flashes after a short period
of operation.

Battery not charged or defective.

•

Fully charge the battery or

•

Replace battery.

Check whether charging process is
working correctly.

•

Check battery contact
terminals or

•

Clean battery contact
terminals.

Indications on Riomote control are
good, but functions are not
performed.

Emergency stop pressed.

Turn button left or right to unlock
emergency stop.

Receiver has no power.

Check fuse.

Replace any blown fuse.

No connection to receiver.

Check all indicator lights for all
functions.

Command via Riomote control not
performed.

Open in electrical circuit.

Check all plug connections.

Push plugs in or

Connect detached plugs.

Check all indicator lights for all
functions.

Receiver defective.

Contact Rioned.

Fault

Cause

Solution

Summary of Contents for CityJet



































































































Search results

Summary of Contents for CityJet

Reviews:

Related manuals for CityJet

Brands by name

Popular brands

Rioned CityJet, User Manual

Search results

Summary of Contents for CityJet

Reviews:

Related manuals for CityJet

Brands by name

Popular brands