Rioned CityJet User Manual Download Page 81

Page: 81 / 98

MALFUNCTIONS

7.1.10 Troubleshooting

Below you will find a list of faults, their possible causes and the corresponding solution for each cause.

Fault

Cause

Solution

Engine will not start or stops
suddenly.

Fuel tank empty.

Refill the fuel tank.

Main or accessory fuse blown.

Replace defective fuse.

Restart engine.

If the fuse blows again,
contact Rioned.

Battery voltage too low.

Charge the battery or replace the
battery

Air in fuel line.

Bleed air at engine.

Riomote control not switched on.

Turn on the

Riomote control

Repeat procedure from
section ‘

Preparation for use

’.

Riomote control Battery flat.

Charge battery or replace battery.

Water tank empty.

Fill water tank.

Water temperature too high.

Fill water tank or let water cool.

Hydraulic oil temperature too high.

Let oil cool.

Summary of Contents for CityJet



































































































Search results

Summary of Contents for CityJet

Reviews:

Related manuals for CityJet

Brands by name

Popular brands

Rioned CityJet, User Manual

Search results

Summary of Contents for CityJet

Reviews:

Related manuals for CityJet

Brands by name

Popular brands