Ricoh PCU10 Service Training Manual Download Page 126

Page: 126 / 195

2.12.2 Fusing pressure mechanism

The pressure springs press the pressure roller against

the hot roller. The pressure adjusting screw is used to

change how strongly the pressure lever presses against

the shaft of the pressure roller.
When the roller is replaced, turn the pressure release

screw counterclockwise to remove it. Move the

pressure lever to the right to release the pressure.
The pressure roller is surfaced with a Teflon tube to

prevent swelling.

2.12.3 Oil supply mechanism

Oil is applied directly to the hot roller from the oil supply

pad. The rubber metering blade gives the surface a

uniform coat of oil as it scrapes excess oil from the roller

surface. Excess oil collects in the upper oil pan.

Pressure lever

Hot roller

Pressure spring

Pressure

release screw

Fulcrum

Pressure roller

Pressure

adjusting

screw

Oil supply pad

Oil blade

Hot roller

Metering blade

Upper oil pan

Metering blade

Blade pressure spring

Fusing

1 July 1994

2-90

Summary of Contents for PCU10




































































































































































































Search results

Summary of Contents for PCU10

Reviews:

Related manuals for PCU10

Brands by name

Popular brands

Ricoh PCU10, Service Training Manual

Search results

Summary of Contents for PCU10

Reviews:

Related manuals for PCU10

Brands by name

Popular brands