Ricoh PCU10 Service Training Manual Download Page 136

Page: 136 / 195

Duplex paper feed sensor

Two sets of photosensor (light emitters and receivers)

are provided just past the duplex feed roller, similar to

the paper feed tray arrangement.
The 2nd duplex paper feed sensor stops the duplex

paper feed motor temporarily to maintain the amount of

buckle of the paper on the registration roller. The sensor

on side 1 detects misfeeds.
The method used to control the production of flex on the

registration roller is the same as that used on the paper

feed tray.

Duplex paper end sensors

The duplex paper end sensors (one set of light emitter

and receiver) are positioned on the upper side of the

duplex paper delivery roller and the lower side of the

transport belt. Paper end is detected by the sensor.

Upper duplex feed sensor

Reverse roller

Paper

Transport

belt

Lower duplex

feed sensor

Grip roller

Duplex feed roller

Upper duplex paper end sensor (light emitter)

Duplex delivery

roller

Transport

belt

Lower duplex

paper end sensor

(light receiver)

Duplex feed

roller

Reverse roller

Duplex and Paper Exit

1 July 1994

2-100

Summary of Contents for PCU10




































































































































































































Search results

Summary of Contents for PCU10

Reviews:

Related manuals for PCU10

Brands by name

Popular brands

Ricoh PCU10, Service Training Manual

Search results

Summary of Contents for PCU10

Reviews:

Related manuals for PCU10

Brands by name

Popular brands