Ricoh PCU10 Service Training Manual Download Page 172

Page: 172 / 195

2.16 Large Capacity Tray

2.16.1 Main construction

Structural diagram

Construction

The tray motor raises and lowers the tray by the drive

chains. Paper end is detected by the photosensor. The

upper and lower limits are detected by photointerruptors.
An FRR system using a magnetic torque limiter and pa-

per feed motor are employed.
Size detection employs five photointerruptors.
The back fence for the stacked paper automatically

moves from the far side of the tray to the middle of the

tray. This facilitates loading paper on the tray.
Horizontal transport unit driven through the duplex/exit

unit.
The upper transport unit is driven by the transport motor.
Tray lock release mechanism and dehumidification

mechanism.

Transport exit sensor

Transport entrance sensor

Horizontal

transport roller

Upper transport roller

Transport motor

Paper feed motor

Grip roller

Paper feed magnetic clutch

Tray motor

LCT control board

Transport drive belt

Tray drive chain

Power transformer

LCT

Tray drive mechanism

Paper feed and separation

Size detection

Back fence drive mechanism

Horizontal transport unit

Upper transport mechanism

Other mechanisms

Large Capacity Tray

1 July 1994

2-136

Summary of Contents for PCU10




































































































































































































Search results

Summary of Contents for PCU10

Reviews:

Related manuals for PCU10

Brands by name

Popular brands

Ricoh PCU10, Service Training Manual

Search results

Summary of Contents for PCU10

Reviews:

Related manuals for PCU10

Brands by name

Popular brands