Ricoh PCU10 Service Training Manual Download Page 194

Page: 194 / 195

2.18 Operation at Paper Misfeed

2.18.1 Jam sensor

The following sensors check for jams during paper transport.

2.18.2 Jam checking

All paper path sensors on the main body perform both ON and OFF checks. For both the ON and OFF

checks, the sensor may change state within a period that is -- 93.6 ms and + 117 ms from the standard

check timing. For jam checking for the LCT, inverter unit, and sorter, refer to related section.

Fusing exit sensor

Duplex entrance

junction sensor

1st and 2nd

duplex paper

feed sensors

Eject junction

sensor

Eject tray

sensor

Transport

sensor

Inverter

entrance

sensor

Exit

sensor

Inverter

2nd

sensor

Finisher

entrance

sensor

Inverter 3rd

sensor

Jogger unit

entrance

sensor

Separation

sensor

Registration

sensor

Horizontal

transport exit

sensor

1st and

2nd paper

feed

sensors

1st and 2nd

LCT paper

feed sensors

Horizontal

transport

entrance

sensor

Operation at Paper Misfeed

1 July 1994

2-158

Summary of Contents for PCU10




































































































































































































Search results

Summary of Contents for PCU10

Reviews:

Related manuals for PCU10

Brands by name

Popular brands

Ricoh PCU10, Service Training Manual

Search results

Summary of Contents for PCU10

Reviews:

Related manuals for PCU10

Brands by name

Popular brands