Ricoh D067 Service Manual Download Page 297

Page: 297 / 676

SC Tables (Basic: D067/D072)

D067/D068/D069/D072 3-42

Appendix

No.

Definition

Symptom

Possible Cause

Fusing temperature warm-up error

542 A

The fusing temperature rises 7

degrees or less in two seconds; and

this continues 5 times consecutively.

Or, the fusing temperature is not

detected within 25 or 35 seconds.

Defective

thermistor

Incorrect installation of the

thermistor

Defective fusing lamp

Defective power supply unit

Fusing overheat error 1

543 A The fusing temperature detected by

the thermistor is 230

C or higher for

one second.

Defective

thermistor

Defective power supply unit

Fusing overheat error 2

544 A The fusing temperature detected by

the monitor circuit is 250

C or higher

for one second.

Defective

thermistor

Defective power supply unit

Fusing lamp overheat error

545 A After the fusing temperature reaches

the target, the fusing lamp remains

on for 12 seconds.

Defective

thermistor

Incorrect installation of the

thermistor

Defective power supply unit

Unstable fusing temperature

546 A

While the fusing lamp is on, the

fusing temperature varies 50

C or

more within one second; and this

occurs two consecutive times.

Defective

thermistor

Incorrect installation of the

thermistor

Defective power supply unit

Summary of Contents for D067





































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for D067

Reviews:

Brands by name

Popular brands

Ricoh D067, Service Manual

Search results

Summary of Contents for D067

Reviews:

Brands by name

Popular brands