Ricoh D067 Service Manual Download Page 157

Page: 157 / 676

BICU and Controller Board

SM 4-43

D067/D068/D069/D072

cem

Adjus

ent

12. Remove the DIMM [B] if it has been installed.

When replacing the controller board, remove the NVRAMs from the board.

Install the NVRAMs to the new board.

When replacing the NVRAM on the controller board

1. When you replace the NVRAM [A], make sure that the NVRAM is correctly installed.

2. The mark [B] on the NVRAM should be directed to the down side (seem from the back

side of the machine).

3. Reassemble the machine.

4. Copy the old NVRAM data to the new NVRAM with SP5-825 or input the SMC data in

the machine. (For details, refer to the "NVRAM Data Upload/Download [SP5-824/825]"

in the "System Service Mode" of the appendices of the this manual)

When Installing the Printer/Scanner Unit (D468)

Refer to procedure “Controller Board (F/SPF models: D068/D069)” in this section, and

carry out the steps (without step 3).

Summary of Contents for D067





































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for D067

Reviews:

Brands by name

Popular brands

Ricoh D067, Service Manual

Search results

Summary of Contents for D067

Reviews:

Brands by name

Popular brands