RichAuto AutoNow F141 User Manual Download Page 44

Page: 44 / 66

北京锐志天宏科技股份有限公司

Beijing RichAuto S&T Co., Ltd

Forging ahead, create future together!

Press

“

” to move cursor, press “

” to set the value (next value setting is

in the same way), then press “

” to save, the system will check the processing

codes and start to run when the reviewing is completed.

The system code checking is auto mode, user can press “

” to skip the

checking and start to run immediately.

System will remember the checking only when the previous checking is a complete

and correct checking. So that the system won‟t check the same code again next time.

During processing, the screen scrolling display real-time processing speed, operation

time and current line number. P

ress”

” to display all processing information.

Press ”

” again to return to the coordinate display interface.

5.5

Operations during processing

5.5.1

Speed ratio & spindle grade Adjusting

1) Adjust speed ratio

During processing, press “

”can directly change speed ratio, each push on

“

”, the speed ratio will increase or decrease 0.1, Speed ratio: max 1.0, min 0.1; the

Summary of Contents for AutoNow F141



































































Search results

Summary of Contents for AutoNow F141

Reviews:

Related manuals for AutoNow F141

Brands by name

Popular brands

RichAuto AutoNow F141, User Manual

Search results

Summary of Contents for AutoNow F141

Reviews:

Related manuals for AutoNow F141

Brands by name

Popular brands