manualshive.com logo in svg

Renesas RL78/G1P, Hardware User Manual, Page: 463 / 770

Share
Download
Renesas RL78/G1P Hardware User Manual Download Page 463

 

RL78/G1P 

 

CHAPTER  11   SERIAL  ARRAY  UNIT 

R01UH0895EJ0100  Rev.1.00 

 

 

444  

Nov 29, 2019 

11.7.2  UART reception 

UART reception is an operation wherein the RL78/G1P asynchronously receives data from another device (start-stop 

synchronization). 

For UART reception, the odd-number channel of the two channels used for UART is used.  The SMR register of both 

the odd- and even-numbered channels must be set. 

 

UART UART0 

Target channel 

Channel 1 of SAU0 

Pins used 

RxD0 

Interrupt INTSR0 

Transfer end interrupt only (Setting the buffer empty interrupt is prohibited.) 

Error interrupt 

INTSRE0 

Error detection flag 

  Framing error detection flag (FEFmn) 

  Parity error detection flag (PEFmn) 

  Overrun error detection flag (OVFmn) 

Transfer data length 

7, 8 or 9 bits 

Transfer rate 

Max. f

MCK

/6 [bps] (SDRmn [15:9] = 2 or more), Min. f

CLK

/(2 

 2

15

 

 128) [bps]

Note 

 

Data phase 

Non-reverse output (default: high level) 

Reverse output (default: low level) 

Parity bit 

The following selectable 

  No parity bit (no parity check) 

  No parity judgment (0 parity) 

  Even parity check 

  Odd parity check 

Stop bit 

1 bit check 

Data direction 

MSB or LSB first 

 

Note

  Use this operation within a range that satisfies the conditions above and the peripheral functions characteristics 

in the electrical specifications (see 

CHAPTER 27  ELECTRICAL SPECIFICATIONS

). 

 

Remarks 1.

  f

MCK

: Operation clock frequency of target channel 

 

 

f

CLK

:  System clock frequency 

 

2. 

m: Unit number (m = 0), n: Channel number (n = 1), mn = 01 

 

Summary of Contents for RL78/G1P



































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments