manualshive.com logo in svg

Renesas RL78/G1P, Hardware User Manual

Share
Download
Renesas RL78/G1P Hardware User Manual Download Page 299

 

RL78/G1P 

 

CHAPTER  9   A/D  CONVERTER 

R01UH0895EJ0100  Rev.1.00 

 

 

280  

Nov 29, 2019

 

9.6.10  Hardware trigger wait mode (select mode, one-shot conversion mode) 

 

<1>  In the stop status, the ADCE bit of A/D converter mode register 0 (ADM0) is set to 1, and the system enters the 

hardware trigger standby status. 

<2>  If a hardware trigger is input while in the hardware trigger standby status, A/D conversion is performed on the 

analog input specified by the analog input channel specification register (ADS).  The ADCS bit of the ADM0 
register is automatically set to 1 according to the hardware trigger input. 

<3>  When A/D conversion ends, the conversion result is stored in the A/D conversion result register (ADCR, ADCRH), 

and the A/D conversion end interrupt request signal (INTAD) is generated. 

<4>  After A/D conversion ends, the ADCS bit is automatically cleared to 0, and the A/D converter enters the stop 

status. 

<5>  If a hardware trigger is input during conversion operation, the current A/D conversion is interrupted, and 

conversion restarts.  The partially converted data is discarded. 

<6>  When the value of the ADS register is rewritten or overwritten during conversion operation, the current A/D 

conversion is interrupted, and A/D conversion is performed on the analog input respecified by the ADS register.  
The partially converted data is discarded. 

<7>  When ADCS is overwritten with 1 during conversion operation, the current A/D conversion is interrupted, and 

conversion restarts.  The partially converted data is initialized. 

<8>  When ADCS is cleared to 0 during conversion operation, the current A/D conversion is interrupted, the system 

enters the hardware trigger standby status, and the A/D converter enters the stop status.  When ADCE = 0, 
inputting a hardware trigger is ignored and A/D conversion does not start. 

 

Figure 9-26.  Example of Hardware Trigger Wait Mode (Select Mode, One-Shot Conversion Mode)  

Operation Timing 

 

<3> A/D conversion ends.

<3>

ANI1

ADS is rewritten
during A/D conversion
operation (from ANI0
to ANI1).

ADCS is cleared

to 0 during A/D

conversion

operation.

ADCE

Hardware

trigger

ADCS

ADS

A/D

conversion

status

ADCR, 

ADCRH

INTAD

A hardware trigger

is generated.

<1> ADCE is set to 1.

A hardware trigger is

generated during A/D

conversion operation.

Trigger

standby

status

The trigger is not

acknowledged.

Trigger

standby

status

ADCS is automatically

cleared to 0 after

conversion ends.

ADCS is overwritten

with 1 during A/D

conversion operation.

Conversion is
interrupted
and restarts.

Stop status

Data 1
(ANI0)

Stop 

status

Data 2
(ANI0)

Data 3
(ANI0)

Data 2
(ANI0)

Data 4
(ANI0)

Data 3
(ANI0)

Data 5
(ANI1)

Data 6
(ANI1)

Data 7
(ANI1)

Data 5
(ANI1)

Data 7
(ANI1)

Data 8
(ANI1)

ANI0

<2>

<2>

<2>

<2>

<2>

<4>

<4>

<4>

<4>

<5>

<8>

<6>

<3>

<3>

Conversion 
is interrupted
and restarts.

Conversion is
interrupted
and restarts.

Conversion is
interrupted.

Stop status

Stop status

Stop 

status

Stop status

<7>

The trigger is not 

acknowledged.

A/D power supply

 stabilization wait

A/D power supply

stabilization wait

A/D power supply

stabilization wait

A/D power supply

stabilization wait

A/D power supply

stabilization wait

 

 

Summary of Contents for RL78/G1P



































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands