manualshive.com logo in svg

Renesas H8S/2437, Hardware Manual

The Renesas H8S/2437 Hardware Manual is available for free download from manualshive.com. This comprehensive manual provides detailed instructions and specifications for efficiently operating and programming the Renesas H8S/2437 microcontroller. Access this invaluable resource to maximize your product's potential and enhance your project development experience.

Share
Download
background image

 

Rev. 1.00, 09/03, page 54 of 704 

 

3.3 

Operating Mode Descriptions 

3.3.1 Mode 

7 

The CPU can access a 16-Mbyte address space in advanced mode. The on-chip ROM is enabled. 
The initial mode after a reset is single-chip mode, to use the external address space, set the EXPE 
bit in MDCR to 1. 

Normal Extended Mode: 

After a reset, ports 1 and 2 become input ports. 

The address bus can be output when the corresponding port data direction register (DDR) is set to 
1. Port 3 is a data bus, part of port 9 and port A become a bus control signal. When the ABWn bit 
in BCRAn is cleared to 0, port 6 becomes the data bus. (n = 1 to 3) 

Multiplex Extended Mode: 

When using an 8-bit bus, regardless of the data direction register (DDR) setting of port 2, it 
becomes an address output and data input/output port. Port 1 can be used as a general port. 

When using a 16-bit bus, regardless of the data direction register (DDR) setting of port 1 or 2, they 
become address output and data input/output ports. 

Summary of Contents for H8S/2437











































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2437

NEC Univerge SV9300 Migration Manual preview
Univerge SV9300
Brand: NEC Pages: 26
NEC NEAX 2400 Quick Reference Manual preview
NEAX 2400
Brand: NEC Pages: 20
NEC DS2000 IntraMail Instructions preview
DS2000 IntraMail
Brand: NEC Pages: 2
dbx Zone Pro 640 Manual preview
Zone Pro 640
Brand: dbx Pages: 2
dbx 166 Quick Start Manual preview
166
Brand: dbx Pages: 17
Xinje XG Series User Manual preview
XG Series
Brand: Xinje Pages: 76
IDT DBP 7+4 User Manual preview
DBP 7+4
Brand: IDT Pages: 93
UNA AUTOMATION DIFRA Installation Manual preview
DIFRA
Brand: UNA AUTOMATION Pages: 20
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
ZyXEL Communications GS3700 Series Handbook preview
GS3700 Series
Brand: ZyXEL Communications Pages: 215
FONESTAR XO-324 Instruction Manual preview
XO-324
Brand: FONESTAR Pages: 8
EK EK-Quantum Momentum ROG Rampage VI Encore User Manual preview
EK-Quantum Momentum ROG Rampage VI Encore
Brand: EK Pages: 11
Aewin Technologies SCB-9651 User Manual preview
SCB-9651
Brand: Aewin Technologies Pages: 86
Accusys ACS-7630 User Manual preview
ACS-7630
Brand: Accusys Pages: 34
WTI NPS-16HD20-1 User Manual preview
NPS-16HD20-1
Brand: WTI Pages: 178
ActiveEye K9504L-W Operation Manual preview
K9504L-W
Brand: ActiveEye Pages: 35
Thecus N5200BR User Manual preview
N5200BR
Brand: Thecus Pages: 90
ADTRAN NetVanta 4430 Quick Start preview
NetVanta 4430
Brand: ADTRAN Pages: 4

Brands by name

Popular brands

Load more brands