manualshive.com logo in svg

Renesas H8S/2437, Hardware Manual

The Renesas H8S/2437 Hardware Manual is available for free download from manualshive.com. This comprehensive manual provides detailed instructions and specifications for efficiently operating and programming the Renesas H8S/2437 microcontroller. Access this invaluable resource to maximize your product's potential and enhance your project development experience.

Share
Download
background image

 

Rev. 1.00, 09/03, page xxviii of xxxviii 

 

Figure 14.9   Set Timing for OVF Flag ........................................................................................ 410 
Figure 14.10   TWCNT Write-Increment Conflict ....................................................................... 411 
Figure 14.11   Write to START Bit during Free-Running Counter Operation ............................. 411 

Section 15   Watchdog Timer (WDT)

 

Figure 15.1   Block Diagram of WDT .......................................................................................... 417 
Figure 15.2   Watchdog Timer Mode (RST/

NMI

 = 1) Operation................................................. 420 

Figure 15.3   Interval Timer Mode Operation............................................................................... 421 
Figure 15.4   OVF Flag Set Timing .............................................................................................. 421 
Figure 15.5   Internal Reset Signal Generation Timing ................................................................ 422 
Figure 15.6   Writing to TCNT and TCSR ................................................................................... 423 
Figure 15.7   Conflict between TCNT Write and Increment ........................................................ 424 

Section 16   Serial Communication Interface (SCI)

 

Figure 16.1   Block Diagram of SCI ............................................................................................. 426 
Figure 16.2   Data Format in Asynchronous Communication  (Example with 8-Bit Data, Parity, 

Two Stop Bits) ........................................................................................................ 442 

Figure 16.3   Receive Data Sampling Timing in Asynchronous Mode ........................................ 444 
Figure 16.4   Relation between Output Clock and Transmit Data Phase   

(Asynchronous Mode)............................................................................................. 445 

Figure 16.5   Sample SCI Initialization Flowchart ....................................................................... 446 
Figure 16.6   Example of Operation in Transmission in Asynchronous Mode  

(Example with 8-Bit Data, Parity, One Stop Bit) .................................................... 447 

Figure 16.7   Sample Serial Transmission Flowchart ................................................................... 448 
Figure 16.8   Example of SCI Operation in Reception   

(Example with 8-Bit Data, Parity, One Stop Bit) .................................................... 449 

Figure 16.9   Sample Serial Reception Flowchart (1)................................................................... 451 
Figure 16.9   Sample Serial Reception Flowchart (2)................................................................... 452 
Figure 16.10   Example of Communication Using Multiprocessor Format   

(Transmission of Data H'AA to Receiving Station A) .......................................... 454 

Figure 16.11   Sample Multiprocessor Serial Transmission Flowchart ........................................ 455 
Figure 16.12   Example of SCI Operation in Reception  

(Example with 8-Bit Data, Multiprocessor Bit, One Stop Bit).............................. 456 

Figure 16.13   Sample Multiprocessor Serial Reception Flowchart (1)........................................ 457 
Figure 16.13   Sample Multiprocessor Serial Reception Flowchart (2)........................................ 458 
Figure 16.14   Data Format in Clocked Synchronous Communication (LSB-First)..................... 459 
Figure 16.15   Sample SCI Initialization Flowchart ..................................................................... 460 
Figure 16.16   Sample SCI Transmission Operation in Clocked Synchronous Mode .................. 461 
Figure 16.17   Sample Serial Transmission Flowchart ................................................................. 462 
Figure 16.18   Example of SCI Receive Operation in Clocked Synchronous Mode .................... 463 
Figure 16.19   Sample Serial Reception Flowchart ...................................................................... 464 
Figure 16.20   Sample Flowchart of Simultaneous Serial Transmission and Reception............... 466 
Figure 16.21   Sample Flowchart for Mode Transition during Transmission ............................... 470 
Figure 16.22   Pin States during Transmission in Asynchronous Mode (Internal Clock)............. 471 

Summary of Contents for H8S/2437











































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2437

D-Link Express EtherNetwork DFE-670TXD Quick Install Manual preview
Express EtherNetwork DFE-670TXD
Brand: D-Link Pages: 4
DAD DSX 26 User Manual preview
DSX 26
Brand: DAD Pages: 36
D-Link DUB-1320 Quick Install Manual preview
DUB-1320
Brand: D-Link Pages: 2
3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Brand: 3Com Pages: 204
Oracle Talari E1000 Installation Manual preview
Talari E1000
Brand: Oracle Pages: 24
Texas Instruments ThunderLAN TNETE100A Programmer'S Manual preview
ThunderLAN TNETE100A
Brand: Texas Instruments Pages: 179
Supermicro SAS-827HD User Manual preview
SAS-827HD
Brand: Supermicro Pages: 16
ETC Power Control Processor Configuration Manual preview
Power Control Processor
Brand: ETC Pages: 64
Intel Core 2 Quad Q9400 Product Brief preview
Core 2 Quad Q9400
Brand: Intel Pages: 2
FONESTAR XO-324 Instruction Manual preview
XO-324
Brand: FONESTAR Pages: 8
ZyXEL Communications ZyXEL ZyAIR B-120 Quick Installation Manual preview
ZyXEL ZyAIR B-120
Brand: ZyXEL Communications Pages: 20
Arbor Technology Em104P-i2904 Quick Installation Manual preview
Em104P-i2904
Brand: Arbor Technology Pages: 8
ATEN Slideaway CL1008 User Manual preview
Slideaway CL1008
Brand: ATEN Pages: 77
Xantech IR-X10 Installation Instructions Manual preview
IR-X10
Brand: Xantech Pages: 16
ICP DAS USA I-87K Series User Manual preview
I-87K Series
Brand: ICP DAS USA Pages: 31
Raven RFMOW V2 User Manual preview
RFMOW V2
Brand: Raven Pages: 33
ADS Technologies API-800 Installation Manual preview
API-800
Brand: ADS Technologies Pages: 21
Proxim 68568r1 Installation And Management Manual preview
68568r1
Brand: Proxim Pages: 65

Brands by name

Popular brands

Load more brands