background image

2

108539

www.desatech.com

IMPORTANT SAFETY 

INFORMATION

BEFORE OPERATING SAW

1.  Read and understand this owner’s manual before 

operating chain saw. 

2.  Watch what you are doing. Use common sense. 

Do not operate saw when you are tired. 

3.  Use chain saw for cutting wood only. Do not use 

chain saw for purpose not intended. Do not use 

for cutting plastic, masonry, etc.

4.  Only well-instructed adults should operate chain 

saw. Never allow children to operate chain saw.

5.  Use only electrical voltage noted on model plate 

of chain saw.

6.  Use only extension cords marked for outdoor use. 

See page 17 for extension cord requirements.

7.  Do not operate chain saw

•  while under the influence of alcohol, medica-

tion, or drugs

•  in rain or in damp or wet areas

•  where highly flammable liquids or gases are 

present

•  if saw is damaged, adjusted wrong, or not fully 

and securely assembled

•  if trigger does not turn saw on and off. Chain 

must  stop  moving  when  you  release  trigger. 

Have faulty switch replaced by authorized ser-

vice center (see 

Technical Service

, page 21). 

•  while in a hurry

•  while in tree or on a ladder unless trained to 

do so 

8.  Wear snug-fitting clothes when operating chain 

saw. Do not wear loose clothing or jewelry. They 

can get caught in moving saw chain.

9.  Wear the following safety gear when operating 

chain saw.

•  heavy-duty gloves (wear rubber gloves when 

working outdoors)

•  steel-toed safety footwear with non-skid soles

•  eye protection such as safety glasses, goggles, 

or face screen

READ ALL INSTRUCTIONS. 

Make sure you read and understand all in-

structions in 

Important Safety Information

 

on pages 2 through 4. Improper use of this 

chain saw can cause severe injury or death 

from fire, electrical shock, body contact 

with moving chain, or falling wood.

 WARNING: When using an electric 

chain  saw,  basic  safety  precautions 

should always be followed to reduce the 

risk of fire, electric shock, and injury to 

persons, including the following: 

•  safety hard hat

•  ear mufflers or ear plugs

•  hair covering to contain long hair

•  face or dust mask (if working in dusty areas)

10. Before cutting, always provide the following:

•  clear work area

•  secure footing

•  planned retreat path from falling tree

11. Inspect tree before cutting down. Make sure there are 

no dead limbs or branches that may fall on you.

12. To reduce the risk of electric shock, this saw has a 

polarized plug (one blade is wider than the other). 

This plug will fit in a polarized outlet only one 

way. If the plug does not fit fully in the outlet of 

your extension cord, reverse the plug. If it still 

does not fit, a polarized extension cord will be 

necessary. Do not change the plug in any way.

WHILE OPERATING SAW

1.  Stay alert. Use common sense while operating 

chain saw.

2.  Keep  work  area  clean.  Cluttered  areas  invite 

injuries.

3.  Be aware of extension cord while operating chain 

saw. Be careful not to trip over cord. Keep cord 

away from chain and operator at all times. 

4.  Keep  children,  animals,  and  bystanders  away 

from chain saw and extension cord. Only chain 

saw user should be in work area. 

5.  Do not cut down a tree unless you are trained or 

have expert help.

6.  If two or more persons perform bucking and fell-

ing operations at the same time, provide plenty 

of distance between operations. Provide distance 

of at least twice the height of tree being felled.

7.  Secure wood you are cutting by using clamps or 

chocks.

8.  Grip chain saw firmly with both hands. Never 

operate chain saw with one hand. Never use hand 

guard as handle.

9.  Keep finger off trigger until ready to make cut.
10. Before starting chain saw, make sure chain is not 

touching anything.

11. To  guard  against  electrical  shock,  avoid  body 

contact  with  grounded  objects  such  as  pipes, 

fences, and metal posts.

12. Keep all parts of body away from chain when 

saw is running.

13. Do not force chain saw while cutting. Apply light 

pressure. It will do the job better and safer at the 

rate for which it was intended.

14. Cut small brush and saplings with extreme care. 

Slender  material  may  catch  in  chain  and  be 

whipped toward you. This could also pull you 

off balance.

15. When  cutting  limb  or  tree  trunk  that  is  under 

tension, use extreme caution. Be alert for wood 

springing back. When wood tension is released, 

For parts contact: www.PartsFor.com

Summary of Contents for 104316-04































Reviews: