background image

CS-360WES

00-36G-00

1

INTRODUCTION

We are constantly working on technical im-
provement of our products. For this reason, 
technical data, equipment and design are 
subject to change without notice. All speci-
fications and directions in this SERVICE 
DATA are based on the latest product infor-
mation available at the time of publication.

ECHO SERVICE MANUAL Ord. 401-24 
(Model : CS-350WES) contains lots of infor-
mation for servicing this model.

0

SERVICE DATA

CHAIN SAW

ECHO:

 CS-360WES

STAGE    MODEL

(Serial number : 37000001 and after)

CONTENTS

 

page

1 SERVICE INFORMATION

 .............................. 2

1-1 Speci

fi

 cation ............................................... 2 

1-2 Technical data ............................................. 3
1-3 Torque limits................................................ 4
1-4  Special repairing materials ......................... 4
1-5 Service limits............................................... 5
1-6 Special tools ............................................... 6

2 CARBURETTOR ADJUSTMENT PROCEDURE

 .. 7

2-1  General adjusting rules ............................... 7
2-2  Presetting Idle adjust screw, L mixture needle 
and H mixture needle ........................................ 7
2-3 Adjusting carburettor................................... 8

Reference No.

 

00-36G-00

I S S U E D :     2 0 1 2 0 4

Summary of Contents for shindaiwa CS-360WES









Reviews: