Reinhardt MWS 10 Manual Download Page 71

Page: 71 / 141

REINHARDT

System- und Messelectronic GmbH

Bergstr. 33 86911 Diessen-Obermühlhausen Postfach 12 41 D-86908 Diessen Tel. 08196 - 934100

MWS_55_e.indb Page 71

geändert am 04.12.2020 von DO

Manual MWS 55 / MWS 88 / MWS 10 and Sensors 55

to table of contents

MWS SET INCLUDE

x <IP-/MAC-Adresse> [<art>, <art>,...]

<!--MWS SET INCLUDE

x <IP-/MAC-Adresse> [<art>, <art>,...] -->

This command sets the addresses and rights of the users who have access to the station, for each

of the 15 positions (x = 1..15), see

ADMIN SET INCLUDE

MWS SET ADMIN

...

<!--MWS SET ADMIN

... -->

Access to all ADMIN SET – commands, i.e.

MWS SET ADMIN ADDRESS 192.168.1.2

executes the command

ADMIN SET ADDRESS

192.168.1.2, and thus sets the administrator-IP-address.

MWS ETHER

NET ...

<!--MWS ETHER

NET ... -->

Access to all ADMIN ETHER

NET

– commands, i.e.

MWS ETHER IP 192.168.1.9

executes the command

ADMIN ETHERNET IP

192.168.1.9, and thus sets the IP-address of the station.

MWS STATION

...

Access to all ADMIN STATION – commands, i.e.

MWS STATION NAME MyStation

executes the

command

ADMIN STATION NAME

MyStation, and thus sets the name of the station..

MWS REMOVE ...

Access to all ADMIN REMOVE – commands, i.e.

MWS REMOVE ETHER CONNECT *

executes the command

ADMIN REMOVE ETHERNET CONNECTION

*, and thus (temporarly)

closes all TCP- and UDP-connections of the weather station.

Summary of Contents for MWS 10














































































































































Search results

Summary of Contents for MWS 10

Reviews:

Reinhardt MWS 10, Manual, Page: 71 / 141

Search results

Summary of Contents for MWS 10

Reviews: