Reinhardt MWS 10 Manual Download

Page: 131 / 141

MWS_55_e.indb Page 131

Manual MWS 55 / MWS 88 / MWS 10 and Sensors 55

geändert am 04.12.2020 von DO

REINHARDT

System- und Messelectronic GmbH

Fax: 08196/7005 and 1414 email:

[email protected]

Web:

http://www.reinhardt-wetterstationen.de

to table of contents

ADMIN LOCK

*ADMIN LOCK

sets the Flash write protection. No changes in the configuration data are saved anymore (corresponds

to the command! S + 8 via the serial interface). Even the administrator can not make any changes

until the flash was unlocked with ADMIN UNLOCK (or! S-8), (change number / password, etc.).

ADMIN UNLOCK

*ADMIN UNLOCK

disables the flash write protection. Now changes can be made in the configuration data.

This corresponds to the! S-8 command via the serial interface.

ADMIN OFF

*ADMIN OFF

switches off the station in battery mode (and standard mode).

ADMIN SAVE CONFIG

*ADMIN SAVE CONFIG

Saves all current settings in the text file /_system/save/config.sav on the SD card. An existing

config.sav file is saved under the name config.bak in the same directory.

ADMIN LOAD CONFIG

*ADMIN LOAD CONFIG

Loads the file /_system/save/config.sav and transferres the containing information into the flash

memory. This takes about 20 minutes. If the command was sent via the serial interface, a progress

bar is transmitted:

LOAD CONFIG |---------+---------+---------+---------+---------I---------+---------+---------+---------+---------|

Each minus sign corresponds to 1%, each plus sign to 10% and the "I" to 50%.

ATTENTION! If the flash memory is write-protected (ADMIN LOCK), the command will be execu-

ted, but no data will be changed!

Accordingly, the command can only be used meaningfully

with either unlocked flash or in SECURE mode.

ADMIN POWER REMOVE

[ab V3.0242]

*ADMIN POWER REMOVE

Disables the backup battery. The next time the station is staked off, the real-time clock loses the

data, i. the time starts at the following power up at 0 o'clock on 01.01.2000. New data will not be

stored correctly until the time is set correctly again!

ATTENTION! Only supported from board version 1.057!

ADMIN POWER MOUNT

[ab V3.0242]

*ADMIN POWER MOUNT

Activates the backup battery (again) to the controller. This is performed automatically each time

the station is powered, but this can be used to undo an inadvertent ADMIN POWER REMOVE

command.

ATTENTION! Only supported from board version 1.057!

Summary of Contents for MWS 10














































































































































Search results

Summary of Contents for MWS 10

Reviews:

Related manuals for MWS 10

Brands by name

Popular brands

Reinhardt MWS 10, Manual

Search results

Summary of Contents for MWS 10

Reviews:

Related manuals for MWS 10

Brands by name

Popular brands