Reinhardt MWS 10 Manual Download Page 134

Page: 134 / 141

MWS_55_e.indb Page 134

Manual MWS 55 / MWS 88 / MWS 10 and Sensors 55

geändert am 04.12.2020 von DO

REINHARDT

System- und Messelectronic GmbH

Fax: 08196/7005 and 1414 email:

[email protected]

Web:

http://www.reinhardt-wetterstationen.de

to table of contents

9 Instructions for Mounting

9.1 Mounting MWS 55

Instructions for mounting:

MWS4, MWS 5M(V), MWS6, Sensors with logger

Click on picture to enlarge

Step 1:

Check packing on damage.

Take out the complete inner package carefully.

Click on picture to enlarge

Step 2:

Take out the socket with the

weather station from the package.

Click on picture to enlarge

Step 3:

Take out the weather station from

the socket carefully. Keep the packing!

Click on picture to enlarge

Step 4:

Mount the weather stationon a 1" pipe,

adjust it to north and fix it well.

MWS 5 / 6 / Einzelsensoren

file:///G:/Wetter-CD-aktuell/English/Install/ShowMWS5.htm

Summary of Contents for MWS 10














































































































































Search results

Summary of Contents for MWS 10

Reviews:

Reinhardt MWS 10, Manual, Page: 134 / 141

Search results

Summary of Contents for MWS 10

Reviews: