Regency Horizon HZ40E Owners And Installation Manual Download

Page: 25 / 72

Regency Horizon® HZ40E-10 Gas Fireplace

installation

HORIZONTAL TERMINATIONS

RIGID PIPE 4" X 6-5/8

The minimum components required for a basic horizontal

termination are:

1 Horizontal Termination Cap

1 45

Elbow

1 Rigid Pipe Adaptor (#510-994)

1 Wall Thimble

1 Length of pipe to suit wall thickness

(see chart)

Wall thickness is measured from the back standofs to the inside

mounting surface of termination cap. For siding other than vinyl

furring strips may be used, instead of the vinyl siding standof, to

create a level surface to mount the vent terminal. The Terminal

must not be recessed into siding. Measure the wall thickness

including furring strips.

If a Vinyl Siding Standof is required (it must be used with vinyl

siding), measure to outside surface of wall without siding and

add 2 inches.

When using Rigid Vent other than

Simpson Dura-Vent, 3 screws must be

used to secure rigid pipe to adaptor.

This product has been evaluated by Intertek

for using a Rigid Pipe Adaptor in conjunction

with Duravent Direct-Vent, Selkirk Direct-Temp,

Ameri Vent Direct Venting, ICC Excel Direct

and Security Secure Vent systems. Use of

these systems with the Rigid Pipe adaptor is

deemed acceptable and does not afect the

Intertek WHI listing of components.

WARNING:

Do not combine venting components from

diferent venting systems.

However use of the the AstroCap

and FPI

Riser is acceptable with all systems.

The FPI AstroCap

and FPI Riser Vent terminal are certiied for installations using FPI venting systems as well as Simpson Dura-Vent

Direct Vent,

American Metal Products Ameri Vent Direct Vent, Security Secure Vent

, ICC Excel, Selkirk Direct-Temp. AstroCap

is a proprietary trademark of FPI

Fireplace Products International Ltd. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.

Flat Wall Installation

Wall Thickness

(inches)

Vent Length Required

(inches)

4" - 5-1/2"

7" - 8-1/2"

10" - 11-1/2"

12"

9" - 14-1/2'

11" - 14-5/8" Adj. Pipe

15" - 23-1/2"

17" - 24" Adj. Pipe

Adj.Pipe Length

Horizontal

Termination Cap

Wall Thimble

Vinyl Siding

Standoff (Optional)

Rigid Pipe Adapter

45 Elbow

Vent Guard

(Part #946-506/P)

Summary of Contents for Horizon HZ40E









































































Search results

Summary of Contents for Horizon HZ40E

Reviews:

Related manuals for Horizon HZ40E

Brands by name

Popular brands

Regency Horizon HZ40E, Owners And Installation Manual

Search results

Summary of Contents for Horizon HZ40E

Reviews:

Related manuals for Horizon HZ40E

Brands by name

Popular brands