Regency Horizon HZ40E Page 14 Owners And Installation Manual Download

Page: 14 / 72

Regency Horizon® HZ40E-10 Gas Fireplace

installation

OPTIONAL FRAMING KIT

Construct the wood framing, ensure inside dimensions are 53"W x 45-

1/2"H as shown below.

53"

45-1/2"

Bend both side nailing strips from the side of the appliance until

positioned as shown below.

Determine the overall combined thickness of the non-combustible board

+ inished material being used. The nailing strips can be adjusted up to
3-1/4".

Nailing Strips

Adjust the nailing strips by loosening 2 screws on each nailing strip -

adjust and retighten screws.

. Attach both vertical studs and secure using 6 screws (2 at bottom, 2 at

top and 2 on sides) as shown.

NOTE

: Ensure the lat side of the steel stud is facing the wood framing.

(258-025)Flat side out

. Secure horizontal steel header stud with 2 screws per side as per

diagram.

. Slide the unit into position. Hook up gas, venting, electrical and fan (if

purchased) prior to installing the remaining steel studs.

. Secure the large horizontal steel stud as shown with 2 screws per side.

. Secure 2 horizontal studs on the lower side of the appliance with 2

screws per side for each stud as shown.

. Secure 2 vertical studs on either side of the appliance with 4 screws per

side stud as shown.

Large stud

(258-028)

Framing kit parts

Header stud

(258-026)

Horizontal

studs

(258-026)

Vertical studs

(258-027)

Summary of Contents for Horizon HZ40E









































































Search results

Summary of Contents for Horizon HZ40E

Reviews:

Related manuals for Horizon HZ40E

Brands by name

Popular brands

Regency Horizon HZ40E, Owners And Installation Manual

Search results

Summary of Contents for Horizon HZ40E

Reviews:

Related manuals for Horizon HZ40E

Brands by name

Popular brands