background image

68

 | 

Regency Horizon® HZ40E-10 Gas Fireplace

 | 

68

warranty

ty 

Limita

i

ons of Liability:  

The original purchaser’s exclusive remedy under this warranty, and FPI’s sole obliga

i

on under this warranty, 

express or implied, in contract or in tort, shall be limited to replacement, repair, or refund, as outlined above.  IN 
NO EVENT WILL FPI BE LIABLE UNDER THIS WARRANTY FOR ANY INCIDENTAL OR CONSEQUENTIAL COMMERCIAL 
DAMAGES OR DAMAGES TO PROPERTY.  TO THE EXTENT PERMITTED BY APPLICABLE LAW, FPI MAKES NO EXPRESS 
WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN.  THE DURATION OF ANY IMPLIED WARRANTY IS 
LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED ABOVE.  IF IMPLIED WARRANTIES CANNOT BE 
DISCLAIMED, THEN SUCH WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. 
 
Some U.S. states do not allow limita

i

ons on how long an implied warranty lasts, or allow exclusion or limita

i

on of 

incidental or consequen

i

al damages, so the above limita

i

ons or exclusions may not apply to you. 

 
Customers located outside the U.S. should consult their local, provincial or na

i

onal legal codes for addi

i

onal 

terms which may be applicable to this warranty. 
 

How to Obtain Warranty Service:

 

Customers should contact the authorized selling dealer to obtain warranty service.  In the event the authorized 
selling dealer is unable to provide warranty service, please contact FPI by mail at the address listed below.  Please 
include a brief descrip

i

on of the problem and your address, email and telephone contact informa

i

on.  A 

representa

i

ve will contact you to make arrangements for an inspec

i

on and/or warranty service. 

 
Canadian Warrantor: 
 

FPI Fireplace Products Interna

i

onal Ltd.

 

6988 Venture St. 
Delta, Bri

i

sh Columbia 

Canada, V4G 1H4 

 

U.S. Warrantor:  
 

Fireplace Products U.S., Inc.

 

PO Box 2189 PMB 125 
Blaine, WA 
United States, 98231 

 
Or contact the Regency Customer Care Centre at 1-800-442-7432 (phone) / 604-946-4349 (fax) 

 

Product Registra

i

on and Customer Support: 

Thank you for choosing a Regency Fireplace.  Regency strives to be a world leader in the design, manufacture, and 
marke

i

ng of hearth products. To provide the best support for your product, we request that you complete a 

product registra

i

on form at 

h

t

p://www.regency-

re.com/Customer-Care/Warranty-Registra

i

on.aspx

 within 

ninety (90) days of purchase. 

 

Summary of Contents for Horizon HZ40E









































































Reviews: