manualshive.com logo in svg

Regency Horizon HZ40E, Owners And Installation Manual, Page: 47 / 72

Share
Download
Regency Horizon HZ40E Owners And Installation Manual Download Page 47

 

Regency Horizon® HZ40E-10 Gas Fireplace

  |     

47

 

 

|

 

47

installation

19. Reinstall the access panel using the 3 screws from step 16.

20. See the Prolame Remote installation instructions for coding the remote 

handheld to the receiver as well as the operating instructions

21. Reverse steps 7 through 1 to complete the installation.

FCM-COM connector

TO REMOVE THE FAN

 

 

1.

  Turn the power off.

2.  

Reverse the above instructions.

 

Maintenance:

 The sealed bearings are lubricated, there is no need to lu-

bricate them further. (Extra lubricant will cause more lint and dust buildup 

- causing the bearings to prematurely fail).

Regular cleaning and vacuuming of the fan area will add to the life of the 

motor.

IMPORTANT:

These fans collect a lot of dust from within your home. Ensure you 

maintain these fan motors on a regular basis by vacuuming

the fan blades and housing using a soft brush nozzle.

Summary of Contents for Horizon HZ40E









































































Reviews:

No comments