Regency Horizon HZ40E Owners And Installation Manual Download

Page: 12 / 72

Regency Horizon® HZ40E-10 Gas Fireplace

installation

UNIT ASSEMBLY PRIOR TO
INSTALLATION

The nailing Strips must be correctly positioned and attached before unit is
slid into position.

NAILING STRIPS

The nailing strips come attached to the unit. There is 1 plate on each side.
The side nailing strips are secured to the framing.

IMPORTANT NOTE

Framing depth measurement is noted with the nailing strips

set as far forward on the irebox as possible. The nailing

strips can be adjusted back up to 3-1/4” to allow for varying

thicknesses in non-combustible material & wall inishes.

Nailing Strips

INSTALLATION ACCESS PANEL

The unit is equipped with a removable access panel for pre-inish installation

of optional components - this panel is located on the lower front face.

Remove 8 screws to remove access panel.

Easier access to gas connection with panel removed.

Install any optional components with access panel removed.

Reinstall access panel with 8 screws - prior to installing any facing material

Note:

Access panel is no longer accessible once facing material installed.

Installation Access Panel

Summary of Contents for Horizon HZ40E









































































Search results

Summary of Contents for Horizon HZ40E

Reviews:

Related manuals for Horizon HZ40E

Brands by name

Popular brands

Regency Horizon HZ40E, Owners And Installation Manual

Search results

Summary of Contents for Horizon HZ40E

Reviews:

Related manuals for Horizon HZ40E

Brands by name

Popular brands