Regency Horizon HZ40E Page 55 Owners And Installation Manual Download

Page: 55 / 72

Regency Horizon® HZ40E-10 Gas Fireplace

installation

SAFETY SCREEN / INNER DOOR FRAME REMOVAL/INSTALLATION

THE INNER DOOR FRAME (3) MUST BE PURCHASED SEPARATELY IN EITHER STAINLESS STEEL OR BLACK

The inner door trim (1) and safety screen (2) come attached to the ireplace.

Remove the inner door trim and safety screen by pulling the bottom of the

trim towards you as one, then lift up.

. Install screen into inner door frame - secure safety screen by bending in 6

tabs in locations shown below.

. Hook the inner door frame (3) and safety screen assembly (2) over

the inner door trim.

. Bend the center tab up and secure with a screw to attach the inner

door frame/safety screen assembly to the inner door trim

. Attach completed assembly to the glass door on unit.

. Secure the assembly with 1 screw on each side.

Tabs

. Remove screws from inner side of the inner door trim and discard screws

and the brackets. (Brackets not shown). Remove the screen mesh from

inner door trim.

Screw Locations

. HZ42STE only - repeat Steps 1-7 to install screen and door frame on

other side.

SAFETY SCREEN/INNER DOOR FRAME REMOVAL/ INSTALLATION

Summary of Contents for Horizon HZ40E









































































Search results

Summary of Contents for Horizon HZ40E

Reviews:

Related manuals for Horizon HZ40E

Brands by name

Popular brands

Regency Horizon HZ40E, Owners And Installation Manual

Search results

Summary of Contents for Horizon HZ40E

Reviews:

Related manuals for Horizon HZ40E

Brands by name

Popular brands