RAYLASE AXIALSCAN Manual Download | Manualshive

Page: 26 / 71

background image

Chapter 4

Functional description

26

RAYLASE 3-Axis Subsystems for Laser Beam Deflection

MN025 / v2.1.0

For subsystems fitted with a protection window only

4.4

Protection window

1 Mount
2 Protection window

3 Clamp ring
4 Protective cap

Installation instructions

o

Before installation, check the protection window for dirt, scratches or cracks.

-

If the protection window is dirty, it must be cleaned (



page 49, Instructions for

cleaning lenses and protective glasses).

-

If the protection window is scratched or cracked, it must be replaced.

o

Screw the protection window and mount into the beam output on the deflection unit until it

is positioned securely.

Fig. 10

Protection win-
dow

«
...
24
25
26
27
28
...
»

Summary of Contents for AXIALSCAN








































































Reviews:

No comments

Related manuals for AXIALSCAN

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 4

Brand: Hanna Instruments Pages: 2

Brand: Parkside Pages: 94

Brand: Saluki Pages: 312

Brand: Xantrex Pages: 2

Brand: Xaoc Devices Pages: 8

Brand: Yamaha Pages: 6

Brand: Cecomp Pages: 4

Brand: Gates Pages: 112

Brand: Datakom Pages: 2

WARREN ELLIS SIGNATURE TENOR BARITONE

Brand: Eastwood Guitars Pages: 4

Brand: Fluke Pages: 32

Brand: Kawai Pages: 110

Brand: UNI-T Pages: 2

Brand: ACCRETECH Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands