manualshive.com logo in svg

Quantum SDLC 2.7, Installation Manual

Share
Download
Quantum SDLC 2.7 Installation Manual Download Page 117

Installation Guide

111

•

For NodeB do 

Setting Up the RAID

 on page 28 from 

Step 4

 on page 29.

•

Start up NodeA. For NodeB do 

Configuring Cluster Service

 on page 29 from 

Step 4

 on page 30 

(on Windows 2000) or from 

Step 3

 on page 31 (on Windows 2003).

•

On NodeA take Scalar DLC offline. On NodeB do 

Installing Scalar DLC Software

 on page 32, 

steps 3, 5 - 7.

•

(optional) On NodeB do 

Building Client Connections

 on page 139.

•

Take Scalar DLC online and proceed.

Scalar DLC chassis bad

Step 1

Power off failed node.

Step 2

Disconnect all cabling.

Step 3

Move all disk, SCSI cards and fibre cards to the new node.

Step 4

Reconnect cabling and power on new node.

One disk fails in the external RAID

Step 1

Remove the cover and unlock the disk.

Step 2

Remove failed disk and insert new disk

Step 3

Reconstruction will begin. Approximate reconstruction time is 6 hours 

Step 4

Hit the up arrow until buzzer stop shows on display.

Step 5

Hit the yellow button twice

Two disk fail in the external RAID

Step 1

Replace both failed disks.

Step 2

Initialize the RAID. Initialization takes approximately 2 hours.

Step 3

Reinstall the Scalar DLC from scratch

Step 4

Restore database from the back up.

RAID controller fails

Step 1

Power down RAID

Step 2

Disconnect all cabling from RAID

Step 3

Remove all disk from failed RAID

Step 4

Insert disk into new RAID chassis

Step 5

Reconnect cabling and power on

Step 6

Run the Installation for ADTX RAID procedure

Summary of Contents for SDLC 2.7

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands