quadient DS-77iQ Manual Download Page 143

Page: 143 / 156

Editing a job

page 55

Check fold settings,
adjust if needed.

Inserted document
too big.

Envelope not always
ejected from sealer.

Verify the Insert Posi-
tion

on page 43

Check adjustment of
envelope stop posi-
tion and fingers.

Document not inser-
ted deep enough.

Maintenance Sched-
ule

on page 124

Clean sealing area.

Sealing area dirty.

Loading documents
standard feeder tray

on page 64

Loading documents
maxiFeeder

on page

Refill feeder tray.

Feeder tray empty.

No document fed.

Adjusting the Separa-
tion of Special Feed-
ers

on page 48

Adjusting the Separa-
tion of the maxiFeed-
er

on page 67

Adjust the separation.

Separation set too
wide / too tight.

Adjusting the side
guides standard
feeder trays

on page

Adjusting the side
guides maxiFeeder

on page 65

Adjust the side
guides.

Side guides set too
narrow.

Adjusting the side
guides standard
feeder trays

on page

Adjusting the side
guides maxiFeeder

on page 65

Adjust side guides.

Side guides set too
wide.

Skewed documents
fed.

Adjusting the Separa-
tion of Special Feed-
ers

on page 48

Adjust the separation.

Separation set too
wide.

Double documents
fed.

English

139

| Page 139 | Jul-11-2022 07:45 | Fault Finding

Summary of Contents for DS-77iQ





























































































































































Search results

Summary of Contents for DS-77iQ

Reviews:

Related manuals for DS-77iQ

Brands by name

Popular brands

quadient DS-77iQ, Manual

Search results

Summary of Contents for DS-77iQ

Reviews:

Related manuals for DS-77iQ

Brands by name

Popular brands