quadient DS-77iQ Manual Download Page 95 | Manualshive

Page: 95 / 156

background image

• BRE offset: in the case of offset is “yes”, the last document that was added to the

set is shifted from the rest of the set (offsetting, see below).

• Collator stop optimisation: if set to "off", the system does not show a message,

when a collator stop change can improve the system output.

Explanation of BRE offset: if a BRE is longer than the set fold but shorter than the envelope
height, this BRE can get folded (A in the figure). Under certain conditions (see below) you
can prevent the BRE from being folded. In the case of offset “yes”, the BRE is held back
during a certain distance (B in the figure). This means that the trailing edge of the BRE
leaves the collator last. The document is not folded. During the insertion into the envelope
the documents of the set are aligned.

6

English

91

| Page 91 | Jul-11-2022 07:45 | Settings menu

«
...
93
94
95
96
97
...
»

Summary of Contents for DS-77iQ





























































































































































Reviews:

No comments

Related manuals for DS-77iQ

Brand: Oki Pages: 4

Brand: Oki Pages: 20

MC560 MFP CX2032

Brand: Oki Pages: 247

T2150 SprintPro

Brand: Tally Pages: 124

Brand: Citizen Pages: 133

Brand: Oki Pages: 3

Brand: U-Line Pages: 33

Brand: Gestetner Pages: 4

Brand: EcLine Pages: 72

Brand: Magicard Pages: 31

Brand: Canon Pages: 76

Brand: Canon Pages: 396

Brand: Canon Pages: 20

Brand: Canon Pages: 467

Brand: Canon Pages: 40

Brand: Canon Pages: 460

Brand: Canon Pages: 448

Brand: Canon Pages: 404

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands